2
views
0
recommends
+1 Recommend
0 collections
    0
    shares
      • Record: found
      • Abstract: found
      • Article: not found

      Acid catalysed cross-linking of poly vinyl alcohol (PVA) by glutaraldehyde: effect of crosslink density on the characteristics of PVA membranes used in single chambered microbial fuel cells

      Read this article at

      ScienceOpenPublisher
      Bookmark
          There is no author summary for this article yet. Authors can add summaries to their articles on ScienceOpen to make them more accessible to a non-specialist audience.

          Abstract

          In the present study, acid catalysed cross-linking of poly vinyl alcohol (PVA) with varying concentrations of glutaraldehyde was analyzed and the cross-linked PVAs were utilized as membrane separators in single chambered microbial fuel cells (MFCs).

          Abstract

          In the present study, acid catalysed cross-linking of poly vinyl alcohol (PVA) with varying concentrations of glutaraldehyde was analyzed and the cross-linked PVAs were utilized as membrane separators in single chambered microbial fuel cells (MFCs). PVA with varying concentrations (1, 2, 4 and 6%) of glutaraldehyde has resulted in a respective 2.8, 5.6, 32 and 34% of degree of cross-linking in PVA1, PVA2, PVA3 and PVA4 membranes. Due to the reduction of available free volume in membranes, progressive improvements in membrane rigidity with impeded membrane porosity were observed with increasing cross-link densities. In succession, proton conductivities of 7.53 × 10 −3, 8.4 × 10 −4, 1.2 × 10 −4 and 4.5 × 10 −5 S cm −1 were observed from the respective PVA1, PVA2, PVA3, and PVA4 membranes. The increased cross-link density enhanced the mechanical strength but reduced other membrane properties such as water uptake and proton conductivities of the membranes. Further, the cast membranes were assembled as MEAs in open air cathode MFCs where, a maximum power and current density of 119.13 ± 6 mW m −2 and 447.81 ± 18 mA m −2 were observed from PVA3 fitted MFC, using mixed firmicutes as biocatalysts. With increased cross-link density, higher ohmic resistances were observed in MFCs, but due to lower oxygen diffusion in the anode, increased performance was observed from highly cross-linked membranes. Electrogenic firmicutes revealed an overall ∼93.45% of COD removal in 27 days of operation, indicating the efficiency of the respective membranes as separators in MFCs. In general, the study depicts the relevance of different acid catalysed cross-linked PVA membranes in bio-energy conversion from microbial fuel cells.

          Related collections

          Most cited references41

          • Record: found
          • Abstract: not found
          • Article: not found

          FTIR spectroscopy characterization of poly (vinyl alcohol) hydrogel with different hydrolysis degree and chemically crosslinked with glutaraldehyde

            Bookmark
            • Record: found
            • Abstract: found
            • Article: not found

            Power generation in fed-batch microbial fuel cells as a function of ionic strength, temperature, and reactor configuration.

            Power density, electrode potential, coulombic efficiency, and energy recovery in single-chamber microbial fuel cells (MFCs) were examined as a function of solution ionic strength, electrode spacing and composition, and temperature. Increasing the solution ionic strength from 100 to 400 mM by adding NaCl increased power output from 720 to 1330 mW/m2. Power generation was also increased from 720 to 1210 mW/m2 by decreasing the distance between the anode and cathode from 4to 2 cm. The power increases due to ionic strength and electrode spacing resulted from a decrease in the internal resistance. Power output was also increased by 68% by replacing the cathode (purchased from a manufacturer) with our own carbon cloth cathode containing the same Pt loading. The performance of conventional anaerobic treatment processes, such as anaerobic digestion, are adversely affected by temperatures below 30 degrees C. However, decreasing the temperature from 32 to 20 degrees C reduced power output by only 9%, primarily as a result of the reduction of the cathode potential. Coulombic efficiencies and overall energy recovery varied as a function of operating conditions, but were a maximum of 61.4 and 15.1% (operating conditions of 32 degrees C, carbon paper cathode, and the solution amended with 300 mM NaCl). These results, which demonstrate that power densities can be increased to over 1 W/m2 by changing the operating conditions or electrode spacing, should lead to further improvements in power generation and energy recovery in single-chamber, air-cathode MFCs.
              Bookmark
              • Record: found
              • Abstract: found
              • Article: not found

              Electricity generation from swine wastewater using microbial fuel cells.

              Microbial fuel cells (MFCs) represent a new method for treating animal wastewaters and simultaneously producing electricity. Preliminary tests using a two-chambered MFC with an aqueous cathode indicated that electricity could be generated from swine wastewater containing 8320 +/- 190 mg/L of soluble chemical oxygen demand (SCOD) (maximum power density of 45 mW/m2). More extensive tests with a single-chambered air cathode MFC produced a maximum power density with the animal wastewater of 261 mW/m2 (200 omega resistor), which was 79% larger than that previously obtained with the same system using domestic wastewater (146 +/- 8 mW/m2) due to the higher concentration of organic matter in the swine wastewater. Power generation as a function of substrate concentration was modeled according to saturation kinetics, with a maximum power density of P(max) = 225 mW/m2 (fixed 1000 omega resistor) and half-saturation concentration of K(s) = 1512 mg/L (total COD). Ammonia was removed from 198 +/- 1 to 34 +/- 1 mg/L (83% removal). In order to try to increase power output and overall treatment efficiency, diluted (1:10) wastewater was sonicated and autoclaved. This pretreated wastewater generated 16% more power after treatment (110 +/- 4 mW/m2) than before treatment (96 +/- 4 mW/m2). SCOD removal was increased from 88% to 92% by stirring diluted wastewater, although power output slightly decreased. These results demonstrate that animal wastewaters such as this swine wastewater can be used for power generation in MFCs while at the same time achieving wastewater treatment.
                Bookmark

                Author and article information

                Journal
                RSCACL
                RSC Advances
                RSC Adv.
                Royal Society of Chemistry (RSC)
                2046-2069
                2015
                2015
                : 5
                : 101
                : 83436-83447
                Affiliations
                [1 ]Advanced Polymer Laboratory
                [2 ]Department of Polymer Science & Technology
                [3 ]University of Calcutta
                [4 ]Kolkata-700009
                [5 ]India
                Article
                10.1039/C5RA16068E
                110e0c1b-d9e8-4cc3-b94b-cfdbc5abe8f4
                © 2015
                History

                Comments

                Comment on this article