13
views
0
recommends
+1 Recommend
1 collections
    0
    shares
      • Record: found
      • Abstract: found
      • Article: found
      Is Open Access

      Estudo comparativo da influência da razão de sopro nas propriedades de filmes tubulares de PEBD e PEAD Translated title: Comparative study of the influence of blow-up ratio in the properties of HDPE and LDPE extruded blow films

      research-article

      Read this article at

      Bookmark
          There is no author summary for this article yet. Authors can add summaries to their articles on ScienceOpen to make them more accessible to a non-specialist audience.

          Abstract

          O objetivo deste trabalho é avaliar a influência do tipo de poliolefina e da razão de sopro (RS) nas propriedades físicas e térmicas de filmes produzidos em processo de extrusão tubular. No processamento foram utilizados um polietileno de baixa densidade (PEBD) e um polietileno de alta densidade (PEAD) transformados numa linha de extrusão de filme tubular com três RS de 1,5:1; 2,5:1 e 3,5:1. Os resultados das caracterizações físicas dos filmes mostraram maior variação de espessura no perímetro dos filmes tubulares de PEAD, quando comparados aos de PEBD. O aumento da RS causou uma diminuição de amplitude desta variação nos filmes tubulares de PEBD e diferenças nas propriedades ópticas. O coeficiente de atrito (COF) dos filmes foi menor para o PEAD e não teve variação significativa com o aumento da RS utilizada. Em relação às propriedades mecânicas, os filmes de PEAD apresentaram maior resistência à tração e menores valores de deformação no ponto de escoamento em ambas as direções. As RS maiores apresentaram similaridade nas tensões e nas deformações entre as direções da máquina (DM) e transversal (DT). A RS ideal, constatada para os filmes processados com PEBD, é 2,5:1 e com PEAD, é 3,5:1. Os filmes de PEAD apresentaram opacidade maior e menor brilho, quando comparados aos filmes de PEBD. Os resultados comprovaram valores conhecidos na literatura, entretanto introduziu-se uma inovação neste estudo: a utilização da técnica termográfica digital portátil, que permite visualizar, de maneira instantânea (on-line), as variações de temperatura no perímetro do balão, na zona de névoa (região de cristalização ou solidificação do filme).

          Translated abstract

          The purpose of this study is to evaluate the influence of the polyolefin type and the blow-up ratio (BUR) on the thermal physical properties of films produced in a blown film extrusion process. It was used low density polyethylene (LDPE) and high density polyethylene (HDPE) processed in a blown film extrusion line at three BUR of: 1.5:1; 2.5:1 and 3.5:1. The results of physical characterization on these films demonstrated that the increase in the BUR shows a higher thickness variation in the perimeter of tubular films and, therefore, optical properties variation. The coefficient of friction (COF) of the films was smaller for HDPE and did not have significant variation with the increase in the BUR applied. Regarding mechanical properties, HDPE films showed higher tensile strength and lower strain values in the yield point, in both directions. The largest BUR showed higher similarity of the tensions and strains between the machine direction (MD) and transverse direction (TD). The ideal BUR observed for films processed with LDPE is 2.5:1, for HDPE this number is higher and close to 3.5:1. The HDPE films showed more opacities and less brightness when compared to LDPE films. The results prove well known values in the literature, however, there was an innovation introduced in this study which is the use of the portable digital thermo graphic technique that allows the instantaneous visualization (on-line) of the temperature variation in the bubble perimeter in the frost line (crystallization or solidification area of the film).

          Related collections

          Most cited references39

          • Record: found
          • Abstract: not found
          • Book Chapter: not found

          The Chemical Nature of Plastics

            Bookmark
            • Record: found
            • Abstract: not found
            • Book: not found

            Polymer Extrusion

              Bookmark
              • Record: found
              • Abstract: not found
              • Book: not found

              Handbook of Polyethylene: Structures, Properties and Applications

                Bookmark

                Author and article information

                Contributors
                Role: ND
                Role: ND
                Journal
                po
                Polímeros
                Polímeros
                Associação Brasileira de Polímeros (São Carlos )
                1678-5169
                February 2015
                : 25
                : 1
                : 83-93
                Affiliations
                [1 ] Instituto Federal Sul Rio-Grandense Brazil
                [2 ] Universidade Federal do Rio Grande do Sul Brazil
                Article
                S0104-14282015000100011
                10.1590/0104-1428.1618
                dc296868-cfc7-492a-af34-90bb5b58769e

                http://creativecommons.org/licenses/by/4.0/

                History
                Product

                SciELO Brazil

                Self URI (journal page): http://www.scielo.br/scielo.php?script=sci_serial&pid=0104-1428&lng=en
                Categories
                POLYMER SCIENCE

                Polymer science
                LDPE,HDPE,LLDPE,blow-up ratio,frost line,blown film,thermographic,PEBD,PEAD,PELBD,razão de sopro,linha de névoa,filme tubular,termográfica

                Comments

                Comment on this article